Reinitialize your Holosun EPS Carry Red Dot Sight

Wiki Article

Occasionally, you may want to reset your Holosun EPS Carry Red Dot sight to its factory settings. This can be helpful if you've been tinkering with the adjustments or are experiencing unexpected behavior. Fortunately, resetting your Holosun is a simple process that can be performed in just a few procedures.

• First ensuring your red dot sight is powered on.
• Locate the small reset button on the side of the sight.
• Employ a paperclip to depress the reset switch for approximately 5 moments.
• Let go the reset button and your Holosun EPS Carry Red Dot sight will restart.
• Its red dot sight should now be returned to its factory settings.

Return to Your Holosun EPS Carry Red Dot toward Defaults

In case you've tweaked your Holosun EPS Carry red dot settings and want to start fresh, resetting it to its factory configuration is a breeze. First, find the tiny button on the bottom of your optic. Then, press and hold it for around five seconds until you see the red dot blink. Your check here Holosun EPS Carry is now reverted to its factory settings, ready for accurate shooting.

Bring Your Holosun EPS Carry Back to : Functionality

Is your beloved Holosun EPS Carry experiencing some performance problems? Don't despair! A simple factory reset can often fix the problem and get your red dot sight back to its former glory. Before you begin, remember to disconnect the battery from your Holosun EPS Carry to prevent unintended activation during the process.

To perform a factory reset on your Holosun EPS Carry, follow these simple steps:

• Hold down the power button for approximately 5 seconds.
• An indicator will flash, indicating that the reset is being performed.
• Stop pressing the power button once the reset is complete.

Your Holosun EPS Carry should now be back to its factory settings. You can connect the battery and test your sight's functionality. If you encounter any further problems, don't hesitate to contactHolosun's customer support.

Revert Factory Settings on Your Holosun EPS Carry: A Step-by-Step Guide

Resetting your Holosun EPS Carry to factory settings can be a helpful solution if you're experiencing issues with the optic or simply want to start fresh. This process erases all user configurations and returns the sight to its original state. Before proceeding, remember to note down any customizations you have made as they will be lost during this process. Follow these steps carefully to ensure a successful factory reset.

• Initially, Energize your Holosun EPS Carry by pressing the power button.
• Next, press and hold both the mode button and the up/down adjustment button simultaneously.
• During continue holding these buttons, activate the power button once.
• A message will show a confirmation prompt indicating that the reset process is initiated.
• Allow the process to finish. This may take a few moments. Once done, your Holosun EPS Carry will automatically deactivate.

After resetting your Holosun EPS Carry to factory settings, you will need to re-enter any desired customizations, such as brightness levels and reticule style. Refer to the user manual for detailed instructions on configuring your optic after a reset.

Clear All Settings on Your Holosun EPS Carry

To Factory reset your Holosun EPS Carry sight, you'll need to access the settings menu. This can usually be done by Holding a specific button combination. Consult your Guidebook for the exact button sequence for your model. Once in the settings menu, look for an option that says "Reset All". Select this option and confirm the reset. Your sight will then power off and restart with all settings Restored to their default values.

Restore your Holosun EPS Carry via a Factory Standard Settings

If your Holosun EPS Carry is acting funny, a factory reset might be the fix. This will return your sight to its factory settings, clearing any custom configurations you've made. To perform this reset, adhere to these straightforward steps:

• First, find the reset button on your EPS Carry.
• Then, engage a small object, like a paperclip, to activate the reset switch.
• While keep the reset lever engaged, activate your EPS Carry.
• You'll display a message confirming that the reset is complete.

Once the reset is complete, your EPS Carry will be back to its factory settings.

Report this wiki page